Package Include

The post CNC Mach3 4 Axis Manual remote Control USB Pendant DSP JOG encoder for Mach3 first appeared on CNC Controller.

1.Voltage 5V 100PPR.General model, adapt to 98% of the market’s 5V handwheel power supply system
2.Voltage 12V 25PPR.Suitable for Mitsubishi
3.Voltage 24V 100PPR.Suitable for PLC with 24V supply voltage

Pendant Handwheel Features :

1. Cable: (easy to open about 3 meters): imported materials, moderate hardness, can withstand more
than 300,000 times of stretching
2.Housing: New ABS material Corrosion resistant Not easy to break
3.Band switch: FD switch from Taiwan Fuhua Company

Pendant Handwheel Specification :

Unconnected wires must be cut to bare copper，then one after another parcel, Do not touch anything else lines,
components, and housing to avoid causing a short circuit.
1. Please read the manual carefully before wiring, so as not to affect the handwheel operation.
2. The encoder is unable to reverse, the voltage is too high to be burned, usually 5V, such as the new generation
of  Siemens, but Mitsubishi connect 12V, PLC connect 24V.
3. The COM point is the handwheel switch public point, must be connected, otherwise, the switch will not
work properly.
4. The handwheel is light to handle, the collision is easy to be damaged, the rotating code disk and the switch
cannot be too hard, so as not to affect the service life
5. If you don’t have A -, B – signal, you don’t have to connect
6. If Mitsubishi does not have A -, B – signal, PLC does not have A -, B – signal, these signals are not connected.

The post 4 6 Axis MPG Universal Pendant Handwheel Manual Pulse Generator 5V 12V 24V With Emergency Stop For CNC Router Machine NEWCARVE first appeared on CNC Controller.

The Syntec 6A Series controllers incorporate embedded system architectures with 8-inch LCD displays and standard keyboard panels. They include integrated servo axes, spindle axes, MPG (manual pulse generator) axes, as well as USB ports on the front panel. This series provides low prices, high stability, easy operation, and high reliability.

·  3-axis servo positioning control

·  2 spindle DA (+/-10V) sets, including 1 encoder set

·  1 set of dedicated MPG (manual pulse generator) axes, including 7 IN points

·  The 6TA and 6MA come standard with 32I/32O, while the 6CA comes standard with 16I/16O

·  Standard keyboard panel

·   Dedicated port on the operation panel for matrix scanning

·  2 sets of USB ports on the front panel, supporting hot plug-and-play

·  Adapter ( 100~240V AC 50/60Hz ) included

·  Operating environment temperature: 55°C

The post CNC CONTROLLER TAIWAN SYNTEC 6MA 3 Axis CNC Milling Machine Controller LCD displays 3-Axis Servo Positioning Control System first appeared on CNC Controller.

1PCS Lihuiyu m2 nano main board

Description of PM53C Nc Studio Controller Main Board:

1. X-Axis Motor (Contain X Axis Limit, Y Axis Limit)

2. x-axis motor (trolley) engine

3. Y-Axis Motor(Beam Motor)

4. the 5v and 24v’s port

LO: Laser Control Signal Output. High Level-No light Dipping, Low Level(=0.3V)-Laser ON

5V: 5V Switch Power Supply

GND: Ground

24V: 24V Switch Power Supply

5. X Axis Limit, Y Axis Limit

6. The Main Board Code

7. If you use Power Supply, Connect LO to TL.

8. External Synchronous Control Signal Output

The post NEWCARVE Lihuiyu M2 Nano Mother Main Board Laser Control System For DIY 3020 3040 K40 6040 Laser Cutter first appeared on CNC Controller.

1PCS Controller Panel

Description of PM53C Nc Studio Controller Panel:

1. X-Axis Motor (Contain X Axis Limit, Y Axis Limit)

2. x-axis motor (trolley) engine

3. Y-Axis Motor(Beam Motor)

4. the 5v and 24v’s port

LO: Laser Control Signal Output. High Level-No light Dipping, Low Level(=0.3V)-Laser ON

5V: 5V Switch Power Supply

GND: Ground

24V: 24V Switch Power Supply

5. X Axis Limit, Y Axis Limit

6. The Main Board Code

7. If you use Power Supply, Connect LO to TL.

8. External Synchronous Control Signal Output

The post NEWCARVE Lihuiyu Control Panel Board For M2 Nano Main Board CO2 Laser Engraving Cutting Machine Cutter K40 3020 first appeared on CNC Controller.

1PCS Dongle

Description of PM53C Nc Studio Controller Dongle:

1. X-Axis Motor (Contain X Axis Limit, Y Axis Limit)

2. x-axis motor (trolley) engine

3. Y-Axis Motor(Beam Motor)

4. the 5v and 24v’s port

LO: Laser Control Signal Output. High Level-No light Dipping, Low Level(=0.3V)-Laser ON

5V: 5V Switch Power Supply

GND: Ground

24V: 24V Switch Power Supply

5. X Axis Limit, Y Axis Limit

6. The Main Board Code

7. If you use Power Supply, Connect LO to TL.

8. External Synchronous Control Signal Output

The post NEWCARVE Lihuiyu Main Board M2 Nano CO2 Laser Control System Dongle A/B/C DIY 3020 3040 K40 first appeared on CNC Controller.

1PCS LIHUIYU M2 Nano main board

1PCS Dongle

1PCS Control Panel

1PCS Cable

Description of PM53C Nc Studio Controller:

1. X-Axis Motor (Contain X Axis Limit, Y Axis Limit)

2. x-axis motor (trolley) engine

3. Y-Axis Motor(Beam Motor)

4. the 5v and 24v’s port

LO: Laser Control Signal Output. High Level-No light Dipping, Low Level(=0.3V)-Laser ON

5V: 5V Switch Power Supply

GND: Ground

24V: 24V Switch Power Supply

5. X Axis Limit, Y Axis Limit

6. The Main Board Code

7. If you use Power Supply, Connect LO to TL.

8. External Synchronous Control Signal Output

The post LIHUIYU Nano M2 CO2 Laser Main Board + Dongle B + Control Panel Board Corellaser CO2 Laser Stamp Machine K40 3020 3040 NEWCARVE first appeared on CNC Controller.

The post WEIHONG NC studio NK260 NK280 software NC studio V10 3 axis integrated CNC system for cnc engraving machine first appeared on CNC Controller.

Specification parameters of PM53C Nc Studio Controller:

CNC Specification

Number of Axes Supported
three axes

Rotary Axes
X/Y as rotary axis(Optional)

Control Signals

Plus Frequency
160KHZ

Control Mode
Position control

Control Signal Type
Differential signals

Position Signal Type
Pulse+Direction

Communication Mode

PCI

Spindle

Analog Voltage Output
0 – 10v

Tool Management

Tool Measurement Mode
Auto measurement, Manual measurement

Tool Calibration Type
Fixed calibration, Mobile calibration, First calibration  Calibration after tool change

Compensation

Compensation Type
Screw error compensation, Backlash compensation, AQE compensation, Tool compensation

Toolpath Program

Supported File Format
*.g; *.nc; *

Operations

WCS Setting
Supporting WCS G54-G59 and Work Zero saving

Processing Technology
Array function,Mirrorrotate,Cycle

Convenitent Operation
Handwheel guide,Breakpoint resurne,Tool selection

High-speed High-precision Optimization

interpolation algorithms
T-type, S-type and LEP algorithms

Software Language

Chinese,English

Reliability  Safety

CNC Software Alarm
Alarms of program error, operation error, over-travel error, PLC error and IO communication error

Features of PM53C Nc Studio Controller:

The post PM53C Nc Studio Controller 3 Axis Original Weihong Control System For CNC Router NEWCARVE first appeared on CNC Controller.

OR

Specification parameters of Weihong NK105 G2 G3 DSP Controller:

CNC Specifications

Number of Axes SuppORted
three axes

Other Controls
Three axes with multiple cylinders

Hardware Specifications

CPU
ARM11

RAM
128m

FLASH
256m

MonitOR
128*64LCD display module

I/Os
Standard

perfORmance indicatOR
The product stands EMI/Electrical fast transient immunity/Surge immunity tests and confORms to the fourth-grade protection standards of GB/T 17626.5-2008.
Resistance to vibration confORms to the GB/T 2423.10-2008 Standards.
The product stands rigid temperature tests and confORms to the industrial standards of GB/T 2423.102-2008.

Spindle

Multiple Gears
8 gears of spindle speed

Tool Management

Tool Magazine Type
Linear tool magazine

Tool Measurement Mode
Auto measurement, Manual measurement

Tool Measurement Type
Fixed calibration, Mobile calibration, First calibration  Calibration after the tool change

Compensation

Backlash compensation

Toolpath Program

SuppORted
* / * / *.g.nc respectively? ?? / * / * / *.demo.iso.eng / * * / / *..cut.plt / *. txt

Operations

WCS Setting
SuppORting WCS G54-G59

Processing Technology
Array function, Cycle machining

Convenient Operations
Handwheel guide, Breakpoint resume, Tool selection

High-speed High-precision Optimization

interpolation algORithms
T-type and S-type algORithms

Software Language

Chinese, English, Polish, Vietnamese

Reliability  Safety

CNC Software Alarm
Alarms of program errOR, operation errOR, over-travel errOR, PLC errOR, and IO communication errOR

Features of Weihong NK105 G2 G3 DSP Controller:

The post Original Weihong NK105 G2 G3 DSP Controller 3 Axis NC Studio Motion Control System For CNC Router ATC Machine NEWCARVE first appeared on CNC Controller.